Hustler Chainless X5000
The well-designed loading fork on the back of the machine for self-loading and transport of a second bale.
A handy 140L storage box at the front provides space for net and wrap.
Ridges on the feed table mean strings can easily be pulled out from under square bales after they have been loaded.
A large moulded polyethylene feed table provides a low friction surface to feed the bales into the rotor.
Colour-coded handgrips on the hoses make it simple to couple up the machine.
A long ram under the table tilts the table from horizontal to almost vertical, to make sure all material is fed out.
All design and fabrication takes place in Hustler's Hastings factory....
...along with preparation and painting.
Some seriously heavy-duty steel plates are used to mount the loading arm to the chassis.
The easy-to-see load dial at the front shows exactly where the forks are and makes loading simple.
|
|
|
|
|
The well-designed loading fork on the back of the machine for self-loading and transport of a second bale.
|
|
|
|
A handy 140L storage box at the front provides space for net and wrap.
|
|
|
|
|
|
Ridges on the feed table mean strings can easily be pulled out from under square bales after they have been loaded.
|
|
|
|
A large moulded polyethylene feed table provides a low friction surface to feed the bales into the rotor.
|
|
|
|
Colour-coded handgrips on the hoses make it simple to couple up the machine.
|
|
|
|
A long ram under the table tilts the table from horizontal to almost vertical, to make sure all material is fed out.
|
|
|
|
All design and fabrication takes place in Hustler's Hastings factory....
|
|
|
|
...along with preparation and painting.
|
|
|
|
Some seriously heavy-duty steel plates are used to mount the loading arm to the chassis.
|
|
|
|
|
|
The easy-to-see load dial at the front shows exactly where the forks are and makes loading simple.
|
After three years of refinement, testing, and trialling on farms, the Hustler Chainless X5000 trailed bale feeder has been released. Brent Lilley was the lucky ducky sent to review this new piece of farm machinery.
Hastings-based Hustler Equipment has been manufacturing innovative machinery to suit New Zealand conditions for over 50 years. When it set out to build a new, bigger, better bale feeder, the goals were simple: build a machine that could handle any bale thrown at it.
The first thing Hustler did was go to farmers already using its machines and asked them what they wanted. Then, after more than three years and 10,000 hours of refinement, testing, and trialling on farms, the Hustler Chainless X5000 trailed bale feeder was ready for release. And I, for one, was stoked to get the opportunity to check it out first-hand.
Cricklewood Angus operates on Tahaenui Station at Nuhaka, near Wairoa on the east coast. It feeds out a serious amount of supplements over the winter months to its cattle and has recently purchased one of the first production machines out of the factory, albeit after some fairly rigorous testing.
Having already fed hundreds of bales of different types of feed through the machine over the last few months, Cricklewood is more than pleased with its decision and speaks incredibly highly of the machine. For the test, there was a mix of round and square bales of hay and silage on hand to demonstrate just how versatile and easy to use this machine is.
Construction
At first glance, you realise pretty quickly this is a seriously well-thought-out and heavy-duty machine. An adjustable height, 50mm cast, swivel towing eye (rated to a whopping 12 tonnes) is found at the front of a solid single-beam drawbar that allows for tighter turns.
A hose needle incorporated into the drawbar keeps hoses tidy, prevents fouling, and provides storage when they' re not in use. A heavy-duty screwjack makes unhitching easy and is stored out of the way on top of the drawbar, so it's always there when you need it.
Probably the best thing since sliced bread is a 140-litre moulded plastic box that sits above the drawbar in front of the feeding table, providing a convenient storage place for net and plastic wrap keeping it out of the cab. A welcome improvement, however, would be drain holes in the bottom to let that lethal brown silage juice out — easily fixed with a cordless drill.
A box section chassis supports the feed table and distributes the weight to the drawbar and wheels, as well as giving the machine a smooth underside to prevent snagging when crossing over lowered break fences.
Hefty, 60mm, solid square section stub axles at the rear are slightly cambered to ensure the wheels run true to the ground when loaded, for even tyre wear, while a wide wheel track and standard 13/55 R16 tyres increase stability on slopes and minimise compaction.
Moulded polyethylene mudguards are standard and will be welcomed by those who like to keep their machines looking tidy. However, the lack of road-lights may cause problems for those operating on busy roads.
Feed table
A single-piece, non-corrosive moulded polyethelene table, supported on a steel frame, is used to hold the bales as they are fed out, and like the rest of the machine, has been considerably beefed up from earlier models.
By far the single biggest difference though, from any previous model, is the deeper bale chamber and the table has been extended to over five-foot long, for greater flexibility. Although five-foot-wide round bales are not so popular here anymore, they are in other parts of the world Hustler exports to. The added benefit when feeding four-foot-wide bales is there is room around the bale for the operator to remove the net.
Some have also suggested that with some clever loading, it is also now possible to get two smaller, medium square bales on the platform to feed at the same time. So the X5000 has pretty much all bases covered, with the ability to feed bales that are four- or five-foot wide and up to six foot in diameter, and any-sized square bale, although an optional extension for the table is required for bales over 6'6" long.
Rotors
Two rotors on the right-hand side of the machine are at the business end, with five rows of choppers (instead of four), or teeth, on each rotor, and the new, patented axial rotor with paddles that feed towards the centre to keep the bale centred and even on the feed table. Their unique shape, and the fact the top rotor turns three times faster than the bottom, means they will tear even the tightest pack bales apart as they turn.
The top rotor is timed to clean the material of the bottom rotor and a wiper panel ensures material is cleaned off of the top rotor. It is then dropped clear, outside of the machine's wheel track. Cleverly, this wiper panel can be unlocked and lowered to remove any material that gets wedged in between it and the rotor. An optional wiper panel extension can be used for feeding into troughs or over break fences.
The hydraulic drive motor has been moved to the rear to prevent damage if the machine is jack-knifed — a welcome change. Also impressive, the shafts and bearings have been beefed up to a 40mm diameter.
Self-tensioning chains transfer the drive from the motor to the rotors, and are enclosed under a guard to keep the machine safe and tidy, as well as preventing them being covered with hay and mud. The entire drive system is now located under one cover which reduces maintenance.
Loading
The ability to self-load and carry a second bale is a key feature of trailed machines, and the team at Hustler has gone to great lengths to ensure its system is effective, simple, and easy to use. At the back of the machine the loading arm mounts to the chassis directly above the stub axles, for improved stability and weight distribution. Some seriously-thick steel plate, a cast linkage, and a heavy-duty hydraulic ram have been used in the construction of the X5000, to make sure it stands up to the rigours of carrying the heavier 1.5-tonne bales.
New on the X5000 is a load dial on the front of the machine, using a cable to the loading arm to show you exactly what position the rear forks are in at any time, and exactly what position they should be in to achieve your desired operation — very handy once you have a bale on the machine and are picking up a second.
Controls and operation
Controls are kept simple. Under the feed table, a plunger valve diverts oil away from the rotors to the load arm when the feed table is lowered, then back to the rotors when it is raised. Not only does this mean that only two sets of remote valves are required to operate the machine, but it also acts as a safety to guarantee inexperienced operators lower the feed table to the correct position before a bale is loaded.
Feeding is equally as simple. An easy-to-see feed guide shows how high the table should be raised, depending if it is a round or square bale to begin feeding. In practice, the table hardly required moving again when feeding round bales, although squares took a little more attention.
Very handy is the ability to shift bales around with the machine — they can be loaded on the table and carried with the net still on to the desired location, then tipped out over the rotors by raising the feed table right up.
The verdict
The Chainless X5000 is a credit to Hustler. It has been well thought out and very well built. The company has achieved its goal of building a machine that will feed out virtually any size or shape of bale, of almost any type of feed.
For the latest reviews of farm machinery, subscribe to Farm Trader magazine here.
Keep up to date in the industry by signing up to Farm Trader's free newsletter or liking us on Facebook
.jpg)
.jpg)
.jpg)
.jpg)
-1.jpg)
.jpg)
.jpg)
.jpg)
